Solar Simulator AAA Class

SOLAR IV CHARACTERIZATION SYSTEM includes

SOLAR SIMULATOR

I-V CHARACTERIZATION SYSTEM, SOURCEMETER

SAMPLE HOLDER

CONNECTIONS

SOFTWAREs

Solar IV characterization Software

Solar Phototransient Current Software

SPECIFICATIONS

FYTRONIX solar simulators use a single lamp design to meet Class A requirements with 1 SUN output power. FYTRONIX solar simulators are certified to Class AAA for all three of the following standards:

Class: AAA IEC 60904-9 Edition 2 (2007), JIS 8904-9 (2017), and ASTM E927-10 (2015).

• Spectral match: Class A

• Spatial non-uniformity of irradiance, Class A

• Temporal instability, Class A

• Illuminance area: 40 mm diameter

• Variable intensity for 1mW/cm2 to 1000 W(m2 (1 SUN) output

Light source: Plasma light

Advantages  to Xenon lamp and other light sources  are

The life of plasma lamp (4000-5000h)  is longer than Xenon lamp (1000-1500h.

 The output of Plasma lamp is smooth than Xenon lamp.

The intensity of plasma based solar simulator can be controlled from 1 mw/cm² to 100 mw/cm² with 1 step But the intensity of Xenon lamp  based on solar simulator can not controlled from 1 mw/cm² to 100 mw/cm² with 1 step

The intensity of solar light is  controlled by computer (USB communication) . The intensity of the solar simulator is automatically controlled by computer from 1 mw/cm² to 100 mw/cm² with 1 step or any step.

Includes Class AAA calibration certificate for IEC, ASTM and JIS

Sourcemeter

Solarphys Tech

Voltage range: -20 V to +20 V

Voltage resolution: 0.001 V

Current range:  50 pA to 250 mA

-Sample Holder

Connection probes: two probe connection

- Calibrated Reference solar cell to calibrate output to 1 SUN

Factory calibrated AM1.5G spectral match

Factory calibrated intensity

 Calibration bands:  6 bands (400-500nm, 500-600nm, 600-700nm, 700-800nm, 900-1000, 1000- 1100 nm which meets Class AAA specification for IEC 60904-9, JIS C 8912, and ASTM E 927-05 standards.

Easy automatically light adjustment

Can be mounted pointing up, down, or to the side with 90o rotational accessory Temperature controlled for stable output

Software

I-V measurements

P-V measurements

lnI-V measurements

Isc-P (irradiance) measurements

lnIsc vs lnP to analyze photovoltaic mechanism

Sample Holder

Solar Cell I-V Characterization System

This system analyze all photovoltaic and photoconducting characteristics of all solar cells such Dye sensitized solar cells, Quantum dots solar cells, Organic solar Cells, Perovskite Solar Cells, Solar Silicon Solar cells, Thin films solar Cells under 1000 W/m².

This system is a complete current-voltage (I-V) and power-voltage (P-V) measurement environment.

SOLAR SIMULATOR SYSTEM

•           Solar simulator has 7 inch touch screen of the device.

•           Solar spectral spectrum is observed on the screen of the solar simulator controller when the measurement is performed.

•           The solar simulator has  2 inch 90 degree light guide and the light is turned 360 degrees to the desired direction.

•           The illumination area of the device is circular with a diameter of 4

 cm.

•          

SOURCEMETER

•           The sourcemeter must have a sourcemeter. The sourcemeter have an automatic current range and the current range should be in the range  50pA-250 mA.

•           The voltage range of the sourcemeter is ranging from  -20 V to +20 V.

•           The intensity of solar simulator is 1000 W/m²,0-1 SUN

•           The solar simulator measures the IV characteristics of all solar cells (Dye sensitized solar cell, perovskite Solar Cells, Quantum dots solar cells, Organic solar cell, Silicon solar cells) and be able to perform the IV characteristics of the batteries under computer control.

•           The solar simulator measures the current-voltage characteristics of the solar cell under 1

•           The current-voltage (I-V) characteristics of the solar cell are measured with the software in the system. The solar cell's open circuit voltage V_oc, short circuit current I_sc, filling factor FF, maximum current Imax, maximum power P_max and efficiency η, series resistance R_s, shunt resistance Rp and characteristic resistance R_ch should be measured automatically. •

•           A reference solar cell should be given with the solar simulator.

•           The probe holder of the device should be measured in a way that the measurements of the solar cell

SPECIFICATIONS OF SOLAR SIMULATOR SYSTEM

The device comply with the ASTM E 927-05 for uniformity classification, temporal stability and spectral match

Light illumination intensity range is adjustable 1000 W / m²

Device is automatically measure;

a.         open circuit voltage (Voc)

b.         short circuit current (Isc)

c.         fill factor (FF)

d.         voltage at Pmax (Vmax)

e.         current at Pmax (Imax)

f.          maximum output power (Pmax)

g.         shunt resistance (Rsh)

h.         series resistance (Rs)

i.          solar cell characteristics resistance (Rch)

j.          photoresponse (RR)

k.         solar cell efficiency (n)